Recurring Service Plans

 

 

We have encountered this article relating to Tools You Need to Install a New Bathtub below on the net and decided it made sense to write about it with you on my blog.

Mounting a bathtub isn't precisely brain surgery, but it does need strong plumbing, woodworking, and also sometimes, tiling skills. Replacing an old tub with a brand-new one is likewise a reasonably hard task. If the old bathtub is readily available, the job can move immediately; if you need to open up a wall surface to get rid of the old bathtub and also place the brand-new bath tub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will certainly require an assistant to vacate the old bathtub and also embeded in the brand-new one. See to it you have actually certified on your own for the work and also fit trying it. As opposed to working with a service provider to take control of a halfway-completed task, it is far better to take into consideration utilizing one prior to you begin. Possibilities are you may need a professional plumber to make tube connections.
This article will aid you mount a brand-new bath tub in your shower room if you have already bought a brand-new bathtub as well as don't need to change the setup of your previous water system pipes.
Your tools and also material checklist need to consist of the following:

 

• New Tub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Blade


• Tape Measure


• Pipeline Caps


 

Removing Old Touches

If you need to change old taps with new ones as a part of your installment, then the first thing you should do is separate the supply of water. After doing so, turn on the faucets to drain any kind of water staying in the system. The process of getting rid of the existing taps can be fairly troublesome due to the limited gain access to that is often the instance.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the taps. Have a towel all set for the remaining water that will certainly come from the pipelines. When the supply pipelines have been gotten rid of, utilize the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this procedure. When the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned of any type of old sealing compound.
Prior to proceeding to fit the brand-new taps, compare the pipe links on the old faucets to the new taps. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new taps to fit.

 

 

Suitable New Taps

If the tails of the brand-new taps are plastic, after that you will require a plastic connector to stop damage to the string. One end of the connector fits on the plastic tail of the faucet and the various other end offers a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will need reducing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, place the tap in the installing opening in the bath/basin guaranteeing that the washing machines are in location between the tap and also the sink. Secure the tap in position with the manufacturer offered backnut. When the faucet is securely in place, the supply pipes can be attached to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with regular faucet connectors. The former type must be attached to the tap ends first, tightening just by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have been linked.

 

 

Mounting the Bath tub

Using the two wooden boards under its feet, put the tub in the needed placement. The wood boards are helpful in evenly spreading the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 tiny factors.
The following objective is to make certain that the bath tub is leveled all round. This can be achieved by checking the spirit level and adjusting the feet on the bathtub until the spirit level reads level.
To install taps, fit the bottom of the furthest flexible tap connector to the suitable supply pipe by making a compression join; then do the same for the other tap.
Switch on the water supply and also examine all joints as well as brand-new pipework for leakages as well as tighten them if required. Fill the bathtub and also check the overflow electrical outlet and also the regular electrical outlet for leakages.
Lastly, repair the bath paneling as described in the supplier's user's manual. Tiling and also securing around the tub ought to wait until the bathtub has actually been made use of a minimum of once as this will settle it right into its last setting.

 

 

Getting ready for the Installation

To start with, the sustaining framework supplied with the bath needs to be fitted (if called for) according to the maker's directions. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is necessary to make certain that if the tap comes with a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bath, it is additionally practical to fit a supporting plate under the taps device to avoid strain on the bath tub.
Fit the versatile tap adapters to the bottom of the two taps making use of 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bathroom. Utilize the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make sure you make use of all of the provided washers.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath need to now be ready to be suited its final position.

 

 

Tiling Around the Tub

In the area where the bath fulfills the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to crack an inflexible seal, triggering the water to penetrate the wall in between the bath and the tiling, causing complications with moisture and also possible leakages to the ceiling listed below.
You can choose from a selection of coloured sealants to blend in your components and fittings. They are marketed in tubes and cartridges, as well as can securing gaps as much as a size of 3mm (1/8 inch). If you have a larger space to load, you can load it with twists of drenched paper or soft rope. Remember to always fill up the bath tub with water before sealing, to permit the activity experienced when the tub remains in usage. The sealer can break relatively very early if you do not take into account this movement before securing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also quickly readily available on the marketplace. It is advisable to fit the ceramic tiles utilizing waterproof or water-proof glue and grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

Hopefully you enjoyed reading our excerpt on How to Install a Bathtub. Thank you so much for spending some time to read our piece of content. Do you know another person who is enthusiastic about the subject? Feel free to promote it. I am grateful for your time. Visit again soon.

Show Details

Book Now!

 

Have you been hunting for insight concerning How to Install or Replace a Shower Drain?

Updating a washroom is just one of the much more prominent house enhancement jobs. Dealing with the plumbing for draining your shower can be extremely easy unless you overdo it.

 

 

Handling Your Own Shower Drain Installation Task

You can literally build a collection agency for your new shower, but you actually need to think about it. Do you really intend to get involved in the issues of getting the sloping appropriate, not to mention seeing to it every facet of it is waterproof? As well as I suggest every facet! It is much easier to just purchase a pre-cast collector online or at your local Lowes, Residence Depot or equipment store. Structure one could sound like a terrific idea, yet you will most likely feel differently after a couple of hrs.

No matter exactly how you go about obtaining a frying pan, you ought to strive to utilize one that has the drain situated in the exact same spot as the initial pan. Relocating the drain pipelines can be a job, especially if the contractor used a special framing framework. If you are figured out to relocate the drainpipe, you are going to need to cut back the pipeline or lengthen it, which might imply ripping up huge pieces of the floor. Put another way, you are mosting likely to be taking a look at a numerous weekend task.

Presuming we have our drain aligned, the actual hook up is rather simple. The drainage pipe should be encountering vertical approximately the collection agency. It will certainly frequently resemble a "U", which indicates it acts as a cleanout to maintain nasty smells from returning up from the drainpipe. To connect the drainpipe, you are mosting likely to create a water tight link between a drain cap on the top of the frying pan and the drain pipeline. Solutions differ, however you are generally mosting likely to do this by putting a combining item on the top of the drainage pipe. This is after that covered with gaskets and actually screwed right into the drainpipe cap. The drain cap ought to function as a locknut, to wit, it screws straight onto the coupling.

The difficult part of this process is getting your drainpipe cap to fit into a leak-proof setting in the frying pan. This is accomplished by backing off the drain cap once you are sure whatever fits together. Then, you placed plumbing technicians putty around the bottom of the cap and afterwards screw it back on. The putty ought to develop a limited seal in between the cap and also the shower pan, which keeps water from trickling under it and also right into the mounting under the shower.

Obviously, bathroom showers come in a wide variety of styles these days. If you purchase a collector, they generally featured plumbing guidelines or the store can keep in mind anything unusual you must understand. It seems complicated, however is normally quite easy. Enjoy!

Whether you are a bath tub or shower individual, many people search for shower only choices when purchasing a house. This easy fact means greater than a couple of house owners spend a weekend updating or mounting showers in their shower rooms. Luckily for you, it is a relatively easy process.

An enthusiast or frying pan refers to the horizontal surface located at the bottom of the shower. The collector normally includes a non-slip surface a little banked in the direction of the center or anywhere the drain is located. Integrated with three to four inch wall surfaces around the side, the objective of your shower drain plumbing is to get the water to stream to and also down the drain.

STEEL BUILDERS

 

properly installed shower drain can be the difference between staying dry and disaster. The water flowing down your shower drain requires a proper outlet connection; otherwise, you run the risk of flooding.

 

 

With so many different types of drains on offer nowadays (from linear shower drains to grates of all shapes and sizes), there are lessons to be learned about each type before installing one yourself. Whether it’s standard or custom, Steel Builders is here to help you install your shower drain.

 

SMALL FLOOR WASTES

 

Small Floor Waste drain products are available in various patterns and sizes to suit a wide range of uses. Welded from 316 stainless steel, these small floor waste drains provide minimal visual impact and a sleek finish that will make your bathroom or shower stand out.

 

LINEAR SHOWER DRAIN

 

We’d love to tell you that you can just dig a hole, throw a grate on top and call it a day. But when it comes to installing a linear shower drain and grate, there’s a whole world of possibilities that go beyond functionality. Shower drains can actually add a great deal of value to your bathroom, with a variety of designs and finishes available. Get creative with your shower drains.

 

CUSTOM SHOWER GRATES

 

When a standard shower grate installation doesn’t work, you’ll need to consider a custom shower grate and drain modification to suit your application. We offer three top finishes: line patterns, heelguard or tiled inserts.

 

SHOWER GRATE INSTALLATION STEP BY STEP

 

• Start by removing everything to expose the drainage point. Depending on your bathroom and drain size, the drainage point will typically be 50mm, 80mm or 100mm in diameter.


 
• With everything out of the way, install the flange onto the floor, followed by your water stop angles.


 
• Waterproofing. Following Australian Standards, you’ll need to create a slope towards the floor flange. This ensures that any water that penetrates the grout will flow into the drainage point.


 
• With waterproofing complete, it’s time to install the grate. This is where you can start getting creative. Linear shower drain outlets can be installed in the centre, at either end of your shower or at a custom location.


 
• When a standard shower grate doesn’t work, Steel Builders can customise an existing shower grate to length or custom outlet position, which can be welded into place.


 
• Now we have to sand and cement the floor around the shower drain. Remember to leave enough space between the drain to glue your tiles slightly above the drain height.


 
• Fill the joint gap between the shower grate and the tiles with a flexible sealant adhesive to allow for expansion and contraction. Once the sealant has dried, it’s time to enjoy your brand new shower!

 

https://www.steelbuilders.com.au/blogs/news/how-to-install-a-shower-drain-steel-builders

 

We had been made aware of that report on How to Choose the Best Drain for Your Shower from a good friend on our other domain. Do you know another individual who is curious about the subject? Take a moment to share it. Thanks a bunch for your time. Visit us again soon.